1669295

3340320

3341686

3346885

FAST AND A GREAT DEAL 1642203

3347970

3468056

You had better know about wiring for a multi zone system because there is very limited instructions. I have a straight through duct system on my Monaco Dynasty and installation with that meant alot of fabrication.1660220

Giving this set up 4 stars for a couple issues I feel shouldn't have been part of the experience but will spell them out. I did no pics or video as there are plenty out there.

This set up was delivered timely and in perfect condition. I got the old rear unit removed and the new Furrion replaced in just a couple hours. As I did with the front. First bad part. The place they gave for the 110 wiring. The engineers that decided this was ok should be made to install one. I was able to get it put in the spot but it took way longer than it should have. I replaced duo therm units that utilized phone cable t Stat wiring. I was a little skeptical about this. I called e Trailer to inquire about that. They were zero help except for the phone number to the Furrion parent Co. No let me tell you, they were awesome. Wiring schematic emailed in seconds and complete confidence given.
Installs went smoothly. I made a small mistake with electrics but was easily remedied. Next bad note. The plastic for air distribution plate is crap. 1 push in and it was broke. Was able to aluminum tape it up and get it fitted. Fire up and viola! Cold ac. I love the led lighting. The external look is rad. Overall I'm very pleased. Operation is much quieter and I'm hoping much more efficient. If you're on the fence about these units, don't be. These are great units.1624954

Super fast delivery and product was as advertised.3365254

Service & delivery was outstanding Furrion chill cube was delivered on time by ups.
I installed the unit on my Lance SQ805 truck camper. The camper came without AC but was wired for it from the factory (thank goodness).
I rented a material lift from Home Depot it lifted the complete assembly up to 16 feet to load on roof.
Directions for installation were very helpful, I purchased a multi zone unit even though I only needed 1 zone. Muli zone came with a wall thermostat. I mounted it close to the ceiling so it would sense the temperature near the ceiling to keep our bed cool.
I had to run wire through conduit on the ceiling to the thermostat.
Starting temperature was 101F outside, 99F inside
Set thermostat to cool & 72 degrees
After 30 minutes 85F inside
After 1 hour 72F inside & 100F outside
Starting Watts 1290 & 10.66 amps
Maximum power Watts 1439 & 12.87 amps
Fantastic cooling unit!
(I had to contact the manufacturer to get clarification on Dip switch settings to use unit with only one zone, the told me to set all switches to off. An easy adjustment described in the manual. Great service & good customer service!)
Thanks to everyone at etrailer & Lippert mfg. for their service & support.3383739

Click to Enlarge

Click to Enlarge

Click to Enlarge

I purchased the 15K Btu/hr Furrion Chill R32 system to replace a Dometic Brisk Air. The Dometic was noisy and tended to freeze up after about a half hour of use. The Furrion seems to work well and is noticeably quieter than the old AC. So far we haven't seen temperatures much above 80F, so I can't yet say how well it will work when temperatures get into the nineties and above.

The system arrived only two days after it was ordered. Installation was fairly simple. The unit is heavy (~80 lbs) and it took three people to get it on the roof of our camper. This system includes the rooftop unit itself, the air distribution box, a multi-zone controller and a multi-zone thermostat. I didn't need the multi-zone capability, but it works fine as a single zone system.

One obvious difference between the Furrion and our old Dometic AC is the dual fan motors of the Furrion. The Dometic uses a single motor to drive both the evaporator and condenser fans, so setting the fan speed to low slows down the condenser fan. Another difference is how the freeze sensor attaches to the evaporator, using a pre-installed clip to securely hold it where it needs to be. That's a huge improvement over the Dometic freeze sensor, which you just jamb into the evaporator at a random location and hope it doesn't fall out going down the road.

Installation was fairly simple. The Furrion uses a four-wire connection to its thermostat, while the Dometic thermostat is three-wire. Fortunately our thermostat cable had a spare wire, so this wasn't a problem. Also, the furnace thermostat wires for both systems go to AC unit, so that connection was simple. Care needs to be taken to confirm the DIP switch settings inside the controller, which are hard to see. I had to switch on DIP 4 to enable the furnace. There is a foam duct divider shipped inside the AC unit that has to be pulled out and installed between the AC unit and the distribution box.

There didn't seem to be a manual included with the thermostat, although a PDF is available on the Lippert site. Note that the room temperature sensor isn't actually in the 'thermostat', but rather inside the air distribution box intake. There are comments on the web saying that this causes short-cycling, but I haven't seen a problem with our ducted installation. Maybe it's a problem for unducted installations. Kits are available from Castle Winch to relocate the temperature sensor if that's a problem. I believe the furnace temp sensor IS in the thermostat.

There are a bunch of extra wires coming out of the controller, presumably for use in applications that don't accept the standard six pin connector. I capped them off with wire nuts and stowed them in the air intake.

The thermostat is back-lit, making it easy to adjust without turning on a light. When not adjusting the set temperature, the thermostat displays the room temperature. The thermostat has two program settings, although it's not real clear from the manual how they're supposed to work. Although the Furrion has three fan speeds, there's very little difference between them. The auto fan setting seems to work fine.3341399

3385042